Strict Standards: Declaration of ISC_SHIPPING::SaveModuleSettings() should be compatible with ISC_MODULE::SaveModuleSettings($settings = Array, $deleteFirst = true) in /home/ciscooic/public_html/includes/classes/class.shipping.php on line 8

Warning: Creating default object from empty value in /home/ciscooic/public_html/lib/class.log.php on line 67

Strict Standards: Non-static method ISC_SIDEPRODUCTADDTOCART_PANEL::LoadAddToCartOptions() should not be called statically, assuming $this from incompatible context in /home/ciscooic/public_html/includes/display/ProductDetails.php on line 306

Strict Standards: Non-static method ISC_SIDEPRODUCTADDTOCART_PANEL::LoadEventDate() should not be called statically, assuming $this from incompatible context in /home/ciscooic/public_html/includes/display/SideProductAddToCart.php on line 185

Strict Standards: Non-static method ISC_SIDEPRODUCTADDTOCART_PANEL::LoadProductFieldsLayout() should not be called statically, assuming $this from incompatible context in /home/ciscooic/public_html/includes/display/SideProductAddToCart.php on line 186
WIC-1T - ORANGE INFORMATIC COMMUNICATION

RSS Sản phẩm mới

Nhận báo giá


WIC-1T

RRP:
Giá :
6,798,000VND
Mã sản phẩm:
WIC-1T
Vendor:
Cisco Systems, Inc
Thương hiệu:
Cân nặng:
1.45 LBS
Đánh giá:
()
Có Sẵn:
Vận chuyển:
12VND (Sửa giá vận chuyển)
Gift Wrapping:

Số lượng:


Chi tiết sản phẩm

Item No. : WIC-1T
Description: 1-Port Serial WAN Interface Card

Introduction

The 1-port serial WAN interface card (WIC-1T) provides serial connections to remote sites or legacy serial network devices such as Synchronous Data Link Control (SDLC) concentrators, alarm systems, and packet over SONET (POS) devices.

hw_1t_wic1.gif

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

This document is not restricted to specific software and hardware versions.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

Product Number

WIC-1T

One Port Serial WAN Interface Card

 

Features

  • One serial port.

  • Uses the Cisco 60-pin "5-in-1" connector. This connector is DB-60 on one end and can be V.35, RS-232, RS-449, X.21 or EIE-530 on the other end depending on your needs

  • Uses the same cabling as Cisco 2500 and Cisco 7000 serial ports.

  • Does not support hot swap, however no hardware damage will occur if it is swapped while the power is on.

  • Each serial card has one LED, labeled CONN for each port, which lights when the serial port is connected. When the port is in data terminal equipment (DTE) mode, the CONN LED indicates that Data Set Ready (DSR), Data Carrier Detect (DCD), and Clear To Send (CTS) have been detected. When the port is in data communications equipment (DCE) mode, it indicates that Data Terminal Ready (DTR) and Request To Send (RTS) have been detected.

Platform Support

Cisco IOS® Software Support

Cisco 1600

Cisco 1700

Cisco 2600, 2600XM

Cisco 3600

Cisco 3631

Cisco 2691, 3725, 3745

Carrier Module

Not required

Not required

On-board

NM-2W

NM-1E2W, NM-1E1R2W, NM-2E2W

NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W

Not required

On-board

NM-1FE2W, NM-1FE1R2W,

NM-2FE2W, NM-2W

Cisco IOS software support

All Cisco IOS versions

All Cisco IOS versions

All Cisco IOS versions

All Cisco IOS versions

Cisco IOS versions 12.2(13)T and higher

Cisco IOS versions 12.2(13)T, 12.2(11)YT and higher

Sync Max Speed

2.048 Mbps

2.048 Mbps

2.048 Mbps

2.048 Mbps

2.048 Mbps

2.048 Mbps

Async Max Speed

115.2 Kbps

115.2 Kbps

Not supported

Not supported

Not supported

Not supported

Bisync and Half Duplex

Cisco IOS Versions 11.2(8)P and later

All Cisco IOS versions

All Cisco IOS versions

Cisco IOS Versions 11.2(4)XA, 11.3, 11.3T, and all 12.x

Cisco IOS versions 12.2(13)T and higher

Cisco IOS versions 12.2(13)T, 12.2(11)YT and higher

 

Note: All parameters mentioned in this table for the Cisco 1700 series routers are also applicable to Cisco 1800 series routers.

Configuration

This section provides a sample configuration for the WIC-1T interface card.

Note: There are no framing, clocking, or linecode parameters or commands being used here. The WIC-1T interface card does not have an integrated CSU/DSU. You need to use an external CSU/DSU.

Configure the serial interface just as you would any other serial interface. For example,

maui-soho-01(config)#interface Serial 0
maui-soho-01(config-if)#ip add 10.0.0.1 255.255.255.0
maui-soho-01(config-if)#encapsulation ppp
maui-soho-01(config-if)#no shutdown

If your platform supports async, then use the physical-layer async command for async mode. Such an application is useful to connect an external modem to the router. Refer to the document 2 Port Async/Sync WAN Interface Card (WIC-2A/S) for an example.

Cisco Support Community - Featured Conversations

Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers. Below are just some of the most recent and relevant conversations happening right now.


 


Các sản phẩm cùng danh mục

Vendors Other Products

Viết nhận xét

Nhận xét sản phẩm

Sản phẩm này chưa có nhận xét nào. Bạn hãy nhận xét sản phẩm

Tiền tệ

Chọn loại tiền tệ dưới đây

Viet Nam VN VND
United States US Dollar

Danh sách cần mua

Ấn vào nút dưới để cho WIC-1T vào danh sách muốn mua của bạn.

Bạn đã xem




ORANGE INFORMATIC COMMUNICATION
Tòa nhà OIC Số 14 Lô 11A Trung Hòa / Cầu Giấy / Hà Nội

Tel: (84-4) 37332122 - Fax: (84-4) 37338787

OIC chỉ bán sản phẩm Cisco chính hãng có CQ của Cisco System Việt Nam